2 * 50W (100W) -12V semi-flexible flexible single solar panel caravan van for Car RV Marine Boat Trailer
Features:
[Multiple Compatibility] Perfect solar power kit for a variety of off-grid applications like shed, cabin, gate opener, etc where 12V battery is used, as well as to charge and maintain AGM, Flooded, GEL, Deep Cycle and Seal Lead Acid, etc batteries in the car, Rv, boat, marine, trailer, camper, pump, etc.
[Light weight] Made of high efficient solar cells,withstand extreme weather conditions like UV, anti-rusting, IP65 waterproof.
[Intelligent Charging] Optimized 3-stages charging algorithm allows to charge the battery more efficiently, and prevent the battery from overcharge, over-discharge, over-voltage, short circuit, etc, fully protect battery and extend the lifetime.
[Visual Monitor] Visual bright LED indicators help to monitor battery conditions and better understand the status of solar panel and load. Exclusively equipped three working modes for load, allowing to set up the load to work under dusk to dawn automatically plus working hours according to personal requirement, very practical and useful.
solar panel Specification
Maximum power(Pmax) 50W
Output tolerance ± 3%
Maximum system voltage 700V DC
Open circuit voltage(Voc) 19.2V
Short circuit current(Isc) 3.43A
Maximum power voltage(Vmp) 16V
Maximum power current(Imp) 3.15A
Cell efficiency 21%
Operating temperature（NOCT） 45±2℃
Temperature range -40℃～+80℃
Number of cells 32pcs
Weight 1030g
Size 1060*277*2.5 mm
Standard Test Conditions ： lrradiance 1000w/m^2，Temperature 25℃, AM=1.5
Solar panel kit
1、 2*50w solar panels (1060*277MM)
2、 1 set 3m cable with PV connector
3、 1 set 3m cable with Alligator clip
4、 1*10A Controller
5、 1 set 2 in 1 adapter
2pcs Solar Panel
1、 2*50w solar panels (1060*277MM)
12V 220V solar system
1、 2*50w solar panels (1060*277MM)
2、 1 set 3m cable with PV connector
3、 1 set 3m cable with Alligator clip
4、 1*10A Controller
5、 1 set 2 in 1 adapter
6、1 pcs 12V To 220V Inverter
12V 220V solar system
1、 2*50w solar panels (1060*277MM)
2、 1 set 3m cable with PV connector
3、 1 set 3m cable with Alligator clip
4、 1*10A Controller
5、 1 set 2 in 1 adapter
6、1 pcs 12V To 220V Inverter
Controller
1.First,according to the diagram,connect the positive and negative electrodes of the battery to the controller,it will auto-indentify the battery voltage.
2.Then,connect the solar panles to the controller.
3.Finally, connect the positive and negative electrodes of the load to the controller. prevent reverse
4.When using lithium battery with protective panel,set the voltage level to be a fixed value.Do not
set the battery to be automatic indentification.In order to prevent the protection of the lithium battery board from the solar input after starting the controller to indentify the error voltage.
5.The open-circuit voltage of the solar panels must be smaller than the maxium allowable voltage
required by the lithium battery to prevent battery damage from excessive voltage.
6.When using the lithium battery,the short-circuit current of solar panel should be less than 0.3C
(Lithium battery capacity).
Note：
1.When using lithium battery in the environment below 0°C ,lithium battery should be work well at
low temperature.
2.Solar controllers do not have the equalizing function for lithium battery.So,the lithium battery must
build-involtage equalizing function.
3.Please strictly connect the controller in the right order,otherwise it may damage the controller.
4.When remove the cables,please in the reverse order
Felible solar panel
